Invoiced plaster "bark beetle" with his own hands.

Quite often today for finishing both inside and outside the premises used textured plaster "bark beetle".The hands it is applied to various surfaces.It should be said that the technology is paving material is simple.Sure, there are some nuances that need to know.Next, we take a closer look with the material and look at how to make decorative plaster "bark beetle" with his own hands.

General

plaster its name received for the drawing, which is obtained on the surface - it looks like the traces of bark left on the wood.Today, there are two kinds of material."Koroed" may be gypsum or acrylic.First sold in dry form, and the second - as a ready mix.If the whole briefly describe the material, we can say that it is a composite plaster, which contains small stones, beads.Each manufacturer uses in the manufacture of one or another recipe.However, usually as pellets or marbles acts mineral aggregates.Grit material depends on the size of the inclusions.It may be from 0.1 to 3.5 mm.

Benefits material

Through the application of the polymer components instead of sand and mineral filler mixture becomes easy.This prevents unnecessary strain on the structural elements of the building.The decorative plaster "bark beetle" does not contain harmful contaminants, so it is environmentally friendly.The material is resistant to different temperatures.In particular, the coating can withstand drops from -55 to +60 degrees.Plaster is not subject to burn in the sun, is resistant to fire.At higher temperatures the coating does not emit harmful compounds.One of the great advantages of the material is considered to be its longevity.The coating is not exposed to chemicals mold precipitation.Plaster "bark beetle" is not demanding to leave.It quite regularly cleaned with water.Material resistant to mechanical stresses.When washing, you can use a sponge or a vacuum cleaner.Also, the coating can withstand small impacts.The main color is white.It can be changed by adding to a solution of the dye in the preparation.You can also cover the paint dry surface.The material is quite common, and its cost is quite accessible.

possibility of using

Due to its characteristics, the material is used widely today.As mentioned above, the coating can be used both outside and inside the building.For the exterior finish is applied facade plaster "bark beetle".His hands coated snap.From a fantasy owner will depend on the picture, which eventually turn out.Figure formed by various movements by which made the application of plaster "bark beetle".The hands you can create different patterns: wavy, transverse, longitudinal, chaotic.If desired, you can even get a very original picture.

Selection of material before it is applied plaster "bark beetle" with their hands, you must choose the right mix.Manufacturers today are many, each of which uses one or another method of preparing the material.In the selection should pay attention to it and the type of grain.The first characteristic determines the width and depth of grooves, which will be obtained in the process of laying and create a drawing.One feature which has coating is that the consumption of material will depend on the size of the granules.Thus, the plaster with a grain 3.5 mm must be larger than the one in which the filler of 2.5 mm.You also need to decide what will be done with a mixture of work - ready or dry.The latter option is, of course, more preferred.With ready-mix easier and faster to work with.However, its cost is slightly higher.It should be said that properly cooked dry mixture of qualities does not concede finished.

Suitable surface

base on which will be laid plaster "bark beetle" with their hands, should provide a good grip (adhesion).In connection with this coating materials glass, iron is impractical because it just will not be there to stay.The most suitable surface is concrete, bricks, plasterboard.These and similar base without any particular problems laid decorative plaster hands."Bark beetle" is classified as topcoats.In connection with this material is used for masking and grout holes or cracks of the surface.It should be said here that are often carried out not only plaster walls "bark beetle".The hands with the help of this material can be finished and the ceiling.

Tools for

If you want was placed plaster "bark beetle" with their hands should be prepared all necessary.For work required:

  • set of spatulas.
  • bucket.
  • plastic grater.
  • drill with paddle "mixer".
  • Directly mixture itself.

to work is recommended to choose autumn or spring.Stack coating can, of course, and in the summer.However, one should remember that the solution at elevated temperatures will dry quickly, and therefore need to work quickly enough.

Substrate Preparation

before being laid plaster "bark beetle" with his hands, it is necessary to work with the surface.The base should be clean, remove dust, dirt, mold (if any).Next you need to assess the condition of the surface.In the presence of irregularities, cracks or holes should be filled with putty them.As a result, the surface should be relatively flat.The pits must not exceed in this case the grain size of the material.

Primer

After preparation, the base should be treated with a special compound.The paint-primer will provide the necessary adhesion to the surface of the material.The composition should be selected in white or the same color as the covering.This prevents translucence primer through the plaster.If the selected road structure, they can cover the surface in a single layer.He has the necessary quality and thick consistency.If the ground is less expensive, then it will have to be laid in multiple layers.Dries cover about 4-6 hours.After that, you can start plastering.Experts recommend that for best results, use materials of one manufacturer.If we talk about specific manufacturers, then, for example, to render "Cerezyme" in the preparation of the surface is recommended to use the primer CT-16.

Preparation

dry mixture should be diluted according to the manufacturer's instructions.However there are some general guidelines.Thus, in the first tank is filled with water, and then the mixture was poured.Stirred mass using a drill and attachments "mixer".After the mixture reaches the desired consistency, it is necessary to let stand a few minutes, and then mix thoroughly.

Progress

for applying decorative plaster used grater.The tool should be positioned at an angle of 60 degrees.relative to the plane of the treated material and spread over the substrate.The layer will have a thickness corresponding to the grain surface.Once the mixture is applied to the surface stops sticking to the instrument, you can start to form a picture.This is done using a plastic or wooden float.Furrows can be vertical, circular, horizontal, crossed - it all depends on the imagination and preferences.It is recommended to cover the entire surface at a time without smoke breaks and breaks.To dry the material will be about 1-3 days.If you do a good job on the surface it does not show any glossy areas and joints.In general, the coating must be flat and monotonous.